Electro Standards LaboratoriesCranston, RI
 * NOTE: Click on an image to enlarge it in a new window. 
 QuickSwitch 4187 ST Duplex 100 BASE-FX A/B Switch with Remote Access.
QuickSwitch M4187 features: Access either of two separate fiber optic 100 BaseFX ports from a 100 BaseFX COMMON port. The switch is fully compliant with the 802.3u 100Base FX standard. Manual control via pushbutton. Remote control through RS-232 (DB9) serial port. Switch position via LEDs or on computer terminal via remote port. Switch Position memory - in event of a temporary power failure, the siwtch will return to the last ordered position when power is restored.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 4189 4-Way Fiber Optic Switch/Converter
QuickSwitch 4189 Features:
Access any one of four separate fiber optic networks from one computer.
Simple pushbutton switching.
Network ports 1 & 2 are 850 nm 100 Mbps ST duplex multimode fiber optic ports. Network ports 3 & 4 are 1300nm 100 Mbps ST duplex multimode fiber optic ports, ST duplex shown in photo. SC duplex is available.
Internal circuitry insures isolation between networks/devices.
Acts as a signal source, no optical signal loss.
LED display indicates switch position and fiber link presence at a glance.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 4196 4-Way All-Optic Fiber Switch, Multimode, 62.5/125 Microns with a Fully Decouples OFF-LINE Capability.
QuickSwitch Model 4196 features:
Optical Scalability, Bit-Rate Transparent, Service/Protocol Transparent.
A/B/C/D/COMMON SC Duplex Fiber Optic rear panel connectors.
A/B/C/D and OFF-LINE Front-Panel pushbuttons.
Front-panel LEDs display switch positions and power status.
Remote control via voltage excitation.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 4199 Gigabit Fiber Optic A/B/C/D Switch/Converter, SC Multimode, Mirror Switch
QuickSwitch Model 4199 Features:
Optical Scalability, Bit-Rate Transparent, Service/Protocol Transparent, Supports the sharing of a single Gigabyte Ethernet CAT5e RJ45 COM Port or device among four SC Duplex Fiber Optic Interface Devices or Netorkw, 62.5 ohms.
A/B/C/D ports are completely isolated from each other during switching.
Local switching is accomplished by depressing any of the pushbuttons located on the front panel of the unit, A, B, D, D. Led indicators on the front panel display the switch position and power status.
No remote control. Wavelength: 1300 nm.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 4289 4-Way Fiber Optic Switch/Converter
QuickSwitch Model 4289 features.
Access any one of four separate fiber optic networks from one computer.
Simple pushbutton switching eliminates the need to plug/unplug fiber patchcords.
All 4 network ports are 1300nm 100 Mbps ST multimode fiber optic ports, ST duplex shown in pix, SC duplex available.
Internal circuitry insures isolation between network/devices.
Acts as a signal source, no optical signal loss.
LED display indicates switch position and fiber link presence at a glance.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 4294 4-Way All-Optic Simplex Fiber Switch with Threaded FC Connectors, 100/140 Graded Index Fiber, UPC.
QuickSwitch Model 4294 Features:
Optical Scalability.
Bit-Rate and Data Transparent.
Service/Protocol Transparent.
A/B/C/D/COMMON FC Simplex, UPS, not angle polished Rear-Panel Connectors.
Fiber Strand interface: 100/140 graded index multimode fiber.
A/B/C/D Front-panel pushbuttons.
Front-panel LEDs display switch positions and power status.
Remote control via RS232 serial remote port on rear panel.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 5150 Keylock Video Conference Room Secure Switching System
The Model 5150 System consists of:
Model 5008 Display Indicator, Model 5200 Fiber Optic Switch, Model 5502 Ethernet Switch, Model 5503 Telco Switch, and Model 5504 ISDN Switch.

In the Non-Secure mode the system passes the connection of copper and fiber voice and data lines from the conference room equipment to the building data network. In the Secure mode, the system disconnects the same set of lines from the building data network, isolating al of the conference room equipment completely.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 6257 Quad Channel All-Optic A/B Switch Multimode ST Duplex 62.5 Micron with Remote Control Port.
QuickSwitch Model 6257 features:
Fiber switch employs mirror technology.
The switch ports are transparent to all data.
Switch maintains position on power loss and continues to pass data.
Front panel pushbutton control.
Remote control via the custom remote port.
Remote ports allow switch position monitoring.
Front panel LEDs for display of current position of all channels as well as the power status.
All A, B, and COMMON ports are ST Duplex, Multimode 62.5 ohms.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 6270 Fiber Optic SC Duplex A/B Mirror Switch with Remote Serial Control
QuickSwitch Model 6270 Features:
Access either fo two SC Duplex Fiber Optic networks from one computer connected to an SC Duplex COMMON port.
MEMS-based (Micro Electro Mechanical System) multimode mirror switch.
Manual control by pushbutton.
Remote control thru RS-232 (DB9) serial port.
Switch position displayed on front panel LED or on computer terminal via remote port.
Insertion losses are less than 1.0 dB.
The switched Fiber Optic SC Duplex ports are transparent to data and speed.
The switch retains its current position in the event of a power failure.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 6284 Fiber Optic ESCON A/B Mirror Switch with Remote Control
QuickSwitch Model 6284 Features:
Access either of two ESCON Fiber Optic networks from one computer connected to an ESCON COMMON port.
MEMS-based (Micro Electro Mechanical System) multimode mirror switch.
Manual control by the front panel pushbutton.
Remote control via RS-232 (DB9) serial port.
Switch position displayed on front panel LED or on computer terminal via remote port.
Insertion losses are less than 1.0 dB.
The switched Fiber Optic ESCON ports are transparent to all data.
The switch retains its current position in the event of a power failure.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 6284 Fiber Optic ESCON A/B Mirror Switch with Remote Control.
QuickSwitch Model 6284 Features:
Access either of two ESCON Fiber Optic networks from one computer connected to an ESCON COMMON port.
MEMS-based (Micro Electro Mechanical System) multimode mirror switch.
Manual control by the front panel pushbutton.
Remote control through RS-232 (DB9) serial port.
Switch position displayed on front panel LED or on computer terminal via remote port.
Insertion losses are less than 1.0 dB.
The switched Fiber Optic ESCON ports are transparent to all data.
The switch retains its current position in the event of a power failure.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 6290 Fiber Optic Mirror A/B Switch, SC Duplex, Single Mode with Remote.
QuickSwitch features:
Optical Scalability.
Bit-Rate Transparent.
Service/Protocol Transparent.
A/B COMMON SC Duplex fiber optic rear-panel connectors.
A/B front-panel pushbuttons.
Front-panel LEDs display switch position.
Remote control via RS232 (DB9) Serial Remote Port.
MEMS-based Single Mode Mirror Switch provides Gigabyte Network Switching.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 6270 Fiber Optic SC Duplex A/B Mirror Switch with Remote Serial Control
QuickSwitch Model 6270 Features:
Access either of two SC Duplex Fiber Optic networks from one computer connected to an SC Duplex COMMON port.
MEMS-based (Micro Electro Mechanical System) multimode mirror switch.
Manual Control by front panel pushbutton.
Remote control via RS232 (DB9) serial port.
Switch position displayed on front panel LED or on computer terminal via remote port.
Insertion losses are less than 1.0 dB.
The switched Fiber Optic SC Duplex ports are transparent to data and speed.
Switch maintains its current position in event of power failure.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 4192 Fiber Optic SC Duplex A/B/C/D/Off-Line Switch, with Remote, Rackmount
The QuickSwitch Model 4192 allows a fiber optic device connected to the SC duplex COMMON connector of the unit to access any of four fiber optic networks connected to the A, B, C, or D ports, or to disconnect completely from all output ports. Change switch position via pushbuttons or via device connected to the Remote port. Applying appropriate voltage to designated pins of the Remote connector will cause the switch to change position.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch Model 6282 Fiber Optic Mirror A/B Switch, 850 nm SC Duplex, Multimode with Remote.

QuickSwitch 6282 features:
Wavelength: 850nm
Optical Scalability
Bit-Rate Transparent
Service/Protocol Transparent
A, B, and COMMON SC Duplex Fiber Optic Rear-Panel Connectors
A/B Front-Panel Pushbutton
Front-Panel LEDs display Switch position
Remote Control via an RS-232 (DB9) serial port.
MEMS-Based Multimode Mirror Switch provides Gigabyte Network Switching.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 6289 QuickSwitch, fiber optic ST duplex A/B switch w/ contact control remote port.
Model 6289 allows a device connected to common port access to the A or B port. The switch may be controlled locally by manually operating the front panel pushbutton or remotely from a remote toggle switch.
wall mount power module supplied with unit.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 6287 Quick Switch, all optic fiber A/B switch multimode SC Duplex 62.5 micron with remote 10-Base-T LAN Access.
allows user the capability of accessing two seperate Fiber Optic Networks or devices, ports A & B, via connection through a network or device connected to the common port.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 6286 Fiber Optic Mirror A/B Switch, 1300 nm SC Duplex, Multimode with Remote
designed with fiber optic mirror technology. The Signal is received by the unit as an optical signal over the fiber strand, redirected by the mirror mechanisms and leaves the unit as an optical signal over a fiber strand.
Keylock option available as Model 6286K
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 6285 Gigabit Fiber Optic Mirror/Switch Converter w/ Remote Control.
Features access either of two fiber optic networks from one computer connected to a gigabit Ethernet (GigE) RJ45 Common Port.
Dimensions 3"H, 8"D, 8"W, Weighs 2.8 lbs
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 6271 Quick Switch Fiber Optic Duplex A/B Mirror Switch W/ Remote Serial Control.
Enables a device connected to COMMON port to access either of two seperate Fiber Optic networks via SC duplex ports.
Dimensions 1.75"H, 8"D, 19"W Weighs 4.5lbs
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 6264 Six Channel all Optic A/B Switch, LC Duplex with 10 Base-T LAN TELENT access
Allows devices connected to the COMMON port of each channel to access the A or B port on each channel. Switching may be accomplished locally by front panel control or remotley using an Ethernet 10-Base-T connection and Telnet commands.
Dimensions 19"W, 3.5"H, 8"D Weighs 4.5 lbs.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 6195 All Optic Fiber Switch, Multimode, 50/125 Microns with Remote, Rackmount
Allows a fiber optic device connected to the SC duplex COMMON connector of the unit to access any of the four fiber optic networks connected to the A/B/C OR D Ports
Dimension 19'W, 8"D, 3.5"H
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 4185 Fiber Optic SC Duplex, multimode switch/converter. Provides fiber optic link backup.
Allows the user the capability of accessing two seperate fiber optic 100 Base FX ports
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 4184 is a fiber optic SC Duplex Interface A/B Switch.
Connects a workstation or device between two other devices or networks. ensures isolation between the A and B devices or networks.
Includes an RS232 serial security enhanced Supervisory Remote Port. Optional GUI software is available for Windows 95/98/NT/Me/2000/XP
Blueprint  Request Quote Computer and Books   View Literature
 
   
 Model 4181 SC Duplex 100 Base FX Auto Fallback Switch w/ Remote Access
All ports are SC Duplex multimode fiber optic ports. In fallback mode, the unit monitors its environment for SD (SIGNAL DETECT) to determine switch position
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch 4186 Fiber Optic SC Dupex, Multimode A/B/C Switch

- Provides Fiber Optic Link Backup

QuickSwitch 4186 is a fiber optic SC Duplex Interface A/B/C Switch. It has a multimode duplex fiber connector interface on the A, B, C, and COMMON ports. The switch connects a workstation or device between three other devices or networks. The internal circuitry insures isolation between the A, B, and C devices / networks. A great solution for fallback network and sharing applications. A front panel button changes the switch position eliminating the need to plug and unplug fiber patchcords thus minimizing connector wear. Switch position status is displayed on the front panel LEDs.

The standard unit also includes an RS232 serial security enhanced Supervisory Remote Port. Upon proper authentication, a terminal or computer in terminal mode connected to this port can communicate with the unit, determine its status, change the switch position as desired, and/or lockout front panel switching capability. A modem can also be connected to this port for remote access to the switch. Access to the Supervisory Remote Port feature is password protected. An optional graphical user interface (GUI) software is also available for use with a computer running Windows 95/98/NT/Me/2000/XP.

Custom configurations are available.

Specifications
Connectors: (4) SC Duplex ports A, B, C, and COMMON.
Fiber Optic Interface: 1300 nm, 100 Mbps, multimode, full duplex.
Controls: (1) Pushbutton to select port A, B, or C.
Display: (3) Red LEDs display switch position and indicate power presence.
Supervisory Remote Port: (1) DB9/female serial RS232 port.
Power: 115VAC / 60Hz, wall mount supply.
Dimensions: 2"H x 7.5"W x 7"D; 2.8 lbs
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch 4198 8-Way Fiber Optic Switch/Converter w/Remote Control

Features
- Access any one of eight separate fiber optic networks from one computer.
- Simple pushbutton switching eliminates plugging and unplugging fiber optic
patchcords, minimizing connector wear and increasing system reliability.
- All eight network ports are 1300nm 100 Mbps ST duplex multimode fiber
optic ports.
- The COMMON port converts the selected fiber optic network port to the
100BaseTX interface.
- Internal circuitry insures isolation between networks / devices.
- Acts as a signal source, no optical signal loss.
- Remotely control the unit from the RS232 serial Remote port.
- LED display indicates switch position and fiber link presence at a glance.
- Other fiber optic interface network ports are available.
- A 4-Port model is available.

Operation
QuickSwitch 4198 allows the user to access any one of eight separate fiber optic network ports, 1-8 from a computer connected to the COMMON 100BaseTX port. The fiber optic / twisted pair media conversion is built in! Ports 1-8, are 1300nm 100 Mbps ST multimode fiber optic ports. SC duplex is available. Customized configurations are available.

QuickSwitch can be controlled from front panel pushbuttons or remotely via an RS232 serial managment port. Front panel control is as simple as pushing the button of the desired network port. LED indicators display the switch position status, as well as the presence of the fiber optic link. QuickSwitch can be controlled from front panel pushbuttons or remotely via an RS232 serial management port. Front panel control is as simple as pushing the button of the desired network port. LED indicators display the switch position status, as well as the presence of the fiber optic link. QuickSwitch Remote operation enables the remote user to change the switch position, query the switch position status, and lockout front panel operation.

Specifications:
Connectors - Ports 1-8 are 100 Base FX fiber optic ST duplex ports. COMMON port is 100Base-T RJ45.
Fiber Optic Interface - Wavelength 1300nm, speed 100Mbps, multimode fiber, full duplex transmission.
Controls - (8) Pushbuttons to select network port.
Display - (8) Status red LED's; (8) Link red LED's.
Remote Port - RS232 serial port, RJ45 connector.
Power - 115VAC / 60HZ wall mount supply.
Dimensions - 11'W x 2.7"H x 8.5"D, wt. 3 lbs.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch 4374 SC Duplex Fiber to T1 A/B Switch/Converter w/Remote Access

Features
- Access either two Fiber Optic networks from one computer connected to a T1
RJ45 COMMON port.
- High speed fiber optic/copper T1 converter electronics.
- Manual control by the front panel pushbutton.
- Remote control through RS-232 (DB9) serial port.
- Switch position displayed on front panel LED or on computer terminal via
remote port.
- Switch Position Memory: In the event of a temporary power failure, the switch
will return to the last ordered position when power is restored.
- Switch Control: The switch position may be controlled manually via a front panel
pushbutton located on the front of te unit, or remotely from a remote RS-232
serial port located on the rear of the unit. To switch manually simply depress
the front panel pushbutton and the switch will change to the new selected
position as indicated by the front panel LED's. Remote switching of the unit is
done through an RS-232 (DB-9) serial port located on the rear of the
QuickSwitch 4374, which may be connected to any standard RS-232 port on a
computer. The computer, once connected to the remote port, may use any
common terminal emulation software.

Specifications
Connectors: Ports A and B are Fiber Optic SC duplex ports; COMMON Port is T1
RJ-45.
Fiber Optic Port Interface: Ports A & B are fiber optic SC duplex ports that accept
standard fiber optic SC duplex connectors.
Common Port Interface: The Common port is a T1 interface that accepts standard CAT5e patchcords.
Remote Port Interface: RS-232 (DB9) serial port, located on rear of unit, may be connected to any standard RS-232 port or computer.
Controls: Manual Pushbutton or via remote DB9 RS-232 serial port.
Display: Front panel LED or computer terminal via remote port.
Power: 115VAC / 60HZ wall mount supply.
Dimensions: 3" H x 8" D x 8" W
Weight: 2.8 lbs

T1 Network:
A digital transmission link with a capacity of 1.544 Mbps. T1 uses two pairs of normal twisted wires. T1 normally handles 24 voice conversations, each one digitized at 64 Kbps. T1 is a standard digital transmission in the United States. T1 lines are used to connect networks across remote distances. Bridges and routers are used to connect LANs over T1 networks. T1 links can often be connected directly to new PBXs and many new forms of short haul transmission.

T1 lines use time division multiplexing (TDM) to interleave 24 64-Kbps voice or data channels. The standard T1 frame is 193 bits long, which holds 24 8-bit voice samples and one synchronization bit with 8,000 frames transmitted per second. T1 is not restricted to digital voice or to 64 Kpbs data streams. Channels may be combined and the total 1.544 Mbps capacity can be broken up as required.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch 5191 8-Way Fiber Optic Switch/Converter w/Remote Control

- Access any one of eight separate fiber optic networks from one computer.
- Simple pushbutton switching eliminates plugging and unplugging fiber optic
patchcords, minimizing connector wear and increasing system reliability.
- All eight network ports are 1300nm 100 Mbps SC duplex multimode fiber
optic ports.
- The COMMON port converts the selected fiber optic network port to the
100BaseTX interface.
- Internal circuitry insures isolation between networks / devices.
- Acts as a signal source, no optical signal loss.
- Remotely control the unit from the RS232 serial Remote port.
- LED display indicates switch position and fiber link presence at a glance.
- Other fiber optic interface network ports are available.
- A 4-Port model is available.

QuickSwitch 5191 Operation
QuickSwitch 5191 allows the user to access any one of eight separate fiber optic network ports, 1-8, from a computer connected to the COMMON 100BaseTXport. The fiber optic / twisted pair media conversion is built in! Ports 1-8, are 1300nm 100 Mbps SC multimode fiber optic ports. (ST duplex is available) Customized configurations are available.

QuickSwitch can be controlled from front panel pushbuttons or remotely via an RS232 serial management port. Front panel control is as simple as pushing the button of the desired network port. LED indicators display the switch position status, as well as the presence of the fiber optic link. QuickSwitch Remote operation enables the remote user to change the switch position, query the switch position status, and lockout front panel operation.

Specifications
Connectors - Ports 1-8 are 100 Base FX fiber optic SC duplex ports. COMMON port is 100Base-T RJ45.
Fiber Optic Interface - Wavelength 1300nm, speed 100Mbps, multimode fiber, full duplex transmission.
Controls - (8) Pushbuttons to select network port.
Display - (8) Status red LED's; (8) Link red LED's.
Remote Port - RS232 serial port, RJ45 connector.
Power - 115VAC / 60HZ wall mount supply.
Dimensions - 11"W x 2.7"H x 8.5"D, wt. 3lbs.
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch 6275 ST Duplex Fiber Optic 8-Position Switch with OFFLINE position and Remote Serial Control

The QuickSwitch 6275 ST Duplex 8-position Fiber Optic Switch with Remote Serial Control allows the user to switch one Common ST Duplex port to any one of eight ST Duplex ports, or to be switched to an Off-Line position isolating all ports from each other. The system affords local and remote access functionality. Remote access can be accomplished by RS-232 commands sent via the Remote Serial Port. Users can remotely monitor status and control switch functions.

Features:
- One ST duplex fiber optic port is able to access any one of eight ST duplex
ports.
- All fiber optic signals passed through the switch are maintained in fiber
optic light transmission media.
- The switch uses mirror technology and supports gigabyte data rate.
- All ports are ST Duplex, MultiMode, 62.5/125 Micron, 1300nm.
- Front panel pushbutton control or access through the serial data REMOTE
port.
- Front panel LED's display the current switch position and power status.
- Front panel keylock inhibits or permits pushbutton control.
- An Offline position is a valid state to preserve network and data isolation.
- User can configure the switch to either maintain its position and data
pathways on power failure or to revert to the Offline position during power
failure.

Specifications:
Fiber Size: 62.5/125 Micron
Port Connectors: (9) Fiber Optic ST duplex connectors labeled 1 thru 8 and
COMMON.
Remote Control: (1) DB9(F) connector accepts RS232 serial data commands.
Controls: (8) Front panel pushbuttons allow selection of switch position.
Display: (8) Red LED's indicate switch position and power presence.
Keylock: (1) Key operated front panel switch allows lockout of front panel
pushbutton controls.
Power: UL approved 110/120 VAC, 60Hz wall mount power module supplies
12 VAC, 500 mA to the Model 6275.
Dimensions: 19.0" W x 8" D x 3.5" H (2U rack height)
Weight: Approximately 6.0 lbs




Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch 6261 8-Strand Singel Mode Fiber Optic (SMF-28) Mirror A/B Switch, 1310 nm LC with Ethernet Access

The QuickSwitch 6261 8-Strand Fiber Optic LC Switch with 10 Base-T LAN Telnet Access, allows the user the capability of sharing 8 Fiber Optic LC Strands connected to the "COMMON" port among two other sets of 8 strands connected to the "A" and "B" ports with local and remote access functionality. Remote access can be accomplished using an Ethernet 10 Base-T connection and Telnet commands.

Features:
- The switch ports are transparent to all data.
- All switched signals are passed via mirror relays that maintain their
position and continuity even in the event of a power loss or failure.
- Supports Single Mode Fiber Optic wavelength of 1310 nm and gigabit data
rates.
- Control of the switch position is from a 10 Base-T LAN Ethernet
environment or, alternately, the front panel pushbutton.
- Remote Telnet command interface that allows user to control switch
position and obtain switch status.
- Front panel pushbutton may be "locked out" using the remote Telnet
commands.
- Rackmount configuration is standard.

Specifications:
Fiber Size: 8.2/125 Micron (SMF-28)
Port Connectors: (24) LC fiber optic connectors;
(8) group "A" channels
(8) group "B" channels
(8) group "COMMON" channels
Local Control: (1) Front panel pushbutton switches all channels to A or to B,
simultaneously.
Remote Control: (1)RJ45(F) LAN access port accepts RS-232 TELNET Remote
switch control signals.
Display: (2) Red LED's display switch position and power status.
Power: UL approved 120 VAC, 60 Hz wall mount power module supplies 12
VAC, 500 mA to the Model 6261.
Dimensions: 19.0" W x 1.75" H x 8.0" D.
Weight: Approximately 5.5 lbs
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch 6273 ST Duplex Fiber Optic Mirror A/B Switch with Remote Serial Control

The QuickSwitch 6273 ST Duplex Fiber Optic A/B Switch with Remote Serial Control allows one COMMON to access either of two separate fiber optic networks. The system affords local and remote access functionality. Remote access can be accomplished by RS232 commands sent via the Remote Serial Port. Users can remotely monitor status and control of switch functions.

Features:
- The switch uses mirror technology and is transparent to data and speed.
- A/B/COM Ports are ST Duplex, MultiMode 62.5/125 Micron.
- The switch supports Fiber Optic wavelength of 850 nm and gigabyte data
rate.
- Front panel pushbutton control or Remote ASCII Command access through
the serial port.
- Front panel LED's display the current switch position.
- DB9/Female RS232 Serial Port for remote control.
- Switching time less than 1 msec.
- Rackmount configuration is standard.

Specifications
Wavelength: 850 nm
Port Connectors: (3) ST duplex fiber optic rear panel connectors, labeled A, B, COMMON.
Control: Front panel pushbutton allows local selection of switch position.
Remote Control: (1) DB9 (F) connector on rear panel accepts serial RS232.
Display: (2) Red LED's display switch position, status, and power presence.
Power: UL Approved 110/120VAC 60Hz wall mount power module supplies 12VAC, 500 mA to the Model 6273
Dimensions: 19.0" W x 1.75" H x 8.0" D.
Weight: Approximately 4.5 lbs
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch® 6292 Fiber Optic Mirror A/B/C Switch, Single Mode LC Duplex with 10/100 BASE-T LAN TELNET Access

- IP Addressable For Critical Network Alternate-Path Switching!

The QuickSwitch® 6292 Fiber Optic Mirror A/B/C, LC Duplex Switch with 10/100 Base-T LAN Telnet Access allows the user the capability of sharing a Fiber Optic LC Duplex pair connected to the COMMON port among three other sets of LC Duplex pairs connected to the A, B, and C ports with local an dremote access functionality. Remote access can be accomplished using an Ethernet 10/100-Base-T connection and Telnet commands.

Features:
- The switch ports are transparent to all data.
- All switched signals are passed via mirror relays that maintain their
position and continuity even in the event of a power loss or failure.
- Supports single mode fiber (SMF 28), 9/125 micron fiber with a wavelength
of 1310 nm.
- Control of the switch position from a 10/100-Base-T LAN Ethernet
environment
or alternatively, the front panel push button.
- Remote Telnet command interface that allows user to control switch
position and obtain switch status.
- Front panel push button may be "locked out" using the remote Telnet
commands.
- MEMS mirror switch supports OC12 speeds of 622 Mbps.

Specifications:
Wavelength: 1310 nm
Port Connectors: (4) LC Duplex connectors labeled A, B, C, and COMMON.
Control: (1) Pushbutton allows selection of switch position.
Display: (3) Red LED's display switch position and power status.
Supervisory Remote Port: (1) RJ45 (F) connector accepts 10/100 BASE-T LAN Ethernet (TELNET command interface).
Power: UL approved 110/120 VAC 60 Hz wall mount power module supplies 12VAC 500 mA to the Model 6292. Replacement power modules may be ordered using ESL Cat No. 516682.
Dimensions: Standard rackmount, 19.0" W x 1.75" H x 8.0" D.
Weight: Approximately 4.5 lbs
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch® 6293 Fiber Optic Mirror A/B/C Switch, Single Mode LC Duplex with Remote Serial Access

The QuickSwitch® 6293 Fiber Optic Mirror A/B/C, LC Duplex Switch with Remote Serial Access allows the user the capability of sharing a Fiber Optic LC Duplex pair connected to the COMMON port among three other sets of LC Duplex pairs connected to the A, B, and C ports with local and remote acess functionality. Remote access can be accomplished using an RJ45 connection and ASCII commands.

Features:
- The switch ports are transparent to all data.
- All switched signals are passed via mirror relays that maintain their
position and continuity even in the event of a power loss or failure.
- Supports single mode fiber (SMF-28), 9/125 micron fiber with a wavelength
of 1310 nm.
- Control of the switch position from an RJ45 serial port or alternatively, the
front panel push button.
- Remote ASCII command interface that allows user to control switch
position and obtain switch status.
- Front panel push button may be "locked out" using the remote ASCII
commands.
- MEMS mirror switch supports OC12 speeds of 622 Mbps.
- Requires customer supplied -48 VDC, 500 mA power input.

Specifications:
Wavelength: 1310 nm
Port Connectors: (4) LC Duplex connectors labeled A, B, C and COMMON.
Control: (1) Pushbutton allows selection of switch position.
Display: (3) Red LED's display switch position and power status.
Supervisory Remote Port: (1) RJ45 (F) connector accepts ASCII RS232 serial data.
Power: Connector on rear panel accepts customer supplied -48 VDC, 500 mA power input. A mating connector is included along with wiring instructions.
Dimensions: Stanard rackmount, 19.0" W x 1.75" H x 8.0" D.
Weight: Approximately 4.5 lbs
Blueprint  Request Quote Computer and Books   View Literature
 
   
 QuickSwitch® 6212 ST Duplex Fiber Optic 10-Position Switch with Remote Ethernet Port and GUI

INTRODUCTION
The QuickSwitch® 6212 ST Duplex 10-position Fiber Optic Switch with Remote Ethernet Port allows the user to switch one Common ST port to any one of ten ST Duplex ports. The system affords local and remote access functionality. The Remote Ethernet Port allows for both Telnet and GUI remote control. User's can locally or remotely monitor status and control switch functions.

Features:
- One ST duplex fiber optic port is able to access any one fo ten ST duplex
ports.
- All fiber optic signals passed through the switch are maintained in fiber
optic light transmission media.
- The switch uses mirror technology and supports gigabyte data rate.
- All ports are ST Duplex, Multimode, 62.5/125 Micron, 1300nm.
- Control of the switch position from a 10/100-Base-T LAN Ethernet
environment or the front panel pushbuttons.
- Remote Telnet command interface or Graphical User Interface that allow
the user to control switch position and obtain switch status.
- Front panel LED's display the current switch position and power status.
- Remote commands to lock front panel pushbutton control.
- The switch is latching and will maintain its position and continue to pass
data in the event of a power failure.

Software Features:
- Access User Interface via standard web browser.
- Easy to use, simple point and click operation.
- Remotely access to control or monitor the QuickSwitch® 6212 10 Position
Fiber Optic Switch System.
- Users can change the switch's IP address.
- LAN access gives users across the LAN or over the Internet access to
control if user network is configured accordingly.

Specifications:
- Fiber Size: 62.5/125 Micron, 1300nm
- Port Connectors: (11) Fiber Optic ST duplex connectors labeled 1 thru 10
and COMMON.
- Remote Control: (1) DB9(F) connector accepts Telnet and Graphical User
Interface commands.
- Controls: (10) Front panel pushbuttons allow selection of switch position.
- Display: (10) Red LED's indicate switch position and power presence.
- Power: UL approved 110/120 VAC, 60Hz wall mount power module
supplies 12 VAC, 500 mA to the unit.
- Dimensions: 19.0" W x 8" D x 3.5" H (2U rack height)
Weight: Approximately 6.0 lbs
Blueprint  Request Quote Computer and Books   View Literature
 
 
New Search